Handleiding Nintendo Wii Openen

Stap 1 – Faceplate
Gebruik een mesje of zeer platte metalen tool om de witte stickers boven op de schroeven los te krijgen. Doe dit voorzichtig om te voorkomen dat je de stickers kapot maakt.

Stap 2
Verwijder de 2 zwarte Tri-Wing schroeven onder de witte stickers die je net hebt verwijderd. Hiervoor is een speciale Tri-wing schroevendraaier nodig, deze kunt u bij ons bestellen voor 3,95 euro.

Stap 3
Verwijder de zwarte kruis schroef bij de controller poort die het dichtst bij de voorkant van de Wii zit. Deze zit aan de bovenkant van de Nintendo Wii onder het witte klepje.
Stap 4
Gebruik dezelfde tool om het rubbertje te verwijderen aan de onderkant van de Nintendo Wii die het dichtst bij de DVD drive zit.
Stap 5
Verwijder nu de zwarte schroef die onder het rubbertje zit die je net hebt verwijderd

Stap 6
Nu kun je de faceplate van de Nintendo Wii voorzichtig verwijderen. Deze zit nog vast met een kabeltje voor de LED verlichting. Deze kun je los maken met een pincet.
Stap 7
Maak de controller port deksel open zodat je zwarte bezel ziet. Je kunt nu de deksel recht omhoog uit de case trekken.
Doe hetzelfde voor de deksel can de memorycard

Nintendo Wii Moederbord monteren

Step 8
Remove the two remaining 4.1 mm Phillips screws
along the top edge of the black plastic controller port
bezel.
Lift the bezel from the long edge furthest away from the
controller ports and remove it from the Wii.
Step 9
Remove the two 5 mm Phillips screws above the
controller ports.
Installing Nintendo Wii Motherboard

Step 10
Use a metal spudger to remove the three highlighted
screw covers stuck to the side of the Wii.
Step 11
Remove the following screws:
Two 5 mm Phillips screws
One 8.2 mm Tri-wing screw
Step 12
Use a metal spudger to remove the two rubber feet
stuck to the bottom face of the Wii near the rear ports.
Installing Nintendo Wii Motherboard

Step 13
Remove the two 8.2 mm Tri-wing screws hidden under
the feet you just removed.
Step 14
Lift the outer case straight up off the body of the Wii.
Installing Nintendo Wii Motherboard

Step 15 – DVD Drive
Remove the small Phillips screw securing the battery
door to the bottom panel.
This screw is captive to the battery door.
Pull the battery door out of the Wii.
Step 16
Remove the 8.2 mm Tri-wing screw that was hidden
beneath the battery door.
Installing Nintendo Wii Motherboard

Step 17
Remove the two 8.2 mm Tri-wing screws securing the
dvd drive shield near the controller ports.
Step 18
Lift the DVD drive shield upward and remove it from the
Wii.
Step 19
Remove the four 9 mm Phillips screws securing the
DVD drive to the bottom panel.
Installing Nintendo Wii Motherboard

Step 20
Lift the side of the DVD drive opposite the controller
ports enough to access the cables on its bottom face.
Carefully pull the DVD drive power cable out from
under the plastic shroud near the heat sink.
Step 21
Pull the DVD drive power cable away from its socket on
the DVD drive.
Installing Nintendo Wii Motherboard

Step 22
Use your fingernail to flip up the retaining flap on the
DVD drive ribbon cable socket.
Be sure you are prying up on the retaining
flap, not the socket itself.
Pull the DVD drive ribbon cable out of its socket.
Remove the DVD drive from the Wii.
Step 23 – Motherboard Cover
Use a pair of tweezers to lift the fan connector up and
out of its socket on the logic board.
Be sure your tweezers are clamped down
on the fan connector, not the socket on the
motherboard.
Installing Nintendo Wii Motherboard

Step 24
Remove the two 10 mm Phillips screws securing the
fan to the fan shroud.
Remove the fan from the Wii.
Step 25
Use the tip of a spudger or another fine-pointed tool to
carefully pry one of the black plastic retaining fingers
attached to the fan shroud away from the Wi-Fi antenna
board.
Lift the Wi-Fi antenna out of the fan shroud.
Installing Nintendo Wii Motherboard

Step 26
Remove the single 10 mm Phillips screw securing the
second Wi-Fi antenna to the top of the fan shroud.
Step 27
Remove the two pieces of tape securing the second Wi-
Fi antenna cable to the plastic bracket near the heat
sink.
Step 28
Carefully de-route both antennas from the frame of the
Wii and lay them aside.
Installing Nintendo Wii Motherboard

Step 29
Remove the three 10 mm Phillips screws securing the
fan shroud to the Wii.
Lift the fan shroud off the heat sink and remove it from
the Wii.
Step 30
Remove the following six screws securing the EMI
fingers to the bottom panel:
Four 7 mm Phillips screws
Two 11.3 mm Phillips screws
Remove both sets of EMI fingers from the Wii.
Installing Nintendo Wii Motherboard

Step 31
Remove the following three screws:
One 7 mm Phillips screw
Two 10 mm Phillips screws
Lift the bracket out of the Wii.
Step 32
Remove the three 10 mm Phillips screws securing the
black bracket to the bottom panel near the front of the
Wii.
Slightly lift the bracket and use your other hand to pull
the retaining clip away from where the Wi-Fi antennas
enter the motherboard sheild.
Remove the bracket from the Wii.
Be sure not to lose the small square nut
loosely held by the black plastic bracket.
Installing Nintendo Wii Motherboard

Step 33
Remove the nine remaining 7 mm Phillips screws
securing the motherboard cover to the bottom panel.
Step 34
Carefully lift the motherboard cover off the
motherboard, minding any cables that may get caught.
Step 35 – Heat Sink
Remove the four 11.3 mm Phillips screws securing the
heat sink to the bottom panel.
Installing Nintendo Wii Motherboard

Step 36
Lift the heat sink off the motherboard.
When working near the exposed
processors, be sure not to disturb the
thermal pads as the thermal paste may leak
out.
Step 37 – Motherboard
Lift the side of the Wi-Fi board furthest away from the
heat sink and lift it out of its socket on the motherboard,
being careful not to put too much sideways force on the
connector.
Remove the Wi-Fi board & antennas from the Wii.
Step 38
Use the flat end of a spudger or your fingertips to lift up
the end of the Bluetooth board nearest the center of the
motherboard.
Carefully peel the front edge of the Bluetooth board off
the EMI foam attached to the motherboard.
Remove the Bluetooth board.
Installing Nintendo Wii Motherboard

Step 39
Use your fingernail to flip up the DVD drive ribbon cable
retaining flap.
Be sure you are prying up on the retaining
flap, not the socket itself.
Pull the DVD drive ribbon cable out of its socket and
remove it from the Wii.

Step 40
Carefully pull the DVD drive power cable away from its
socket on the motherboard and remove it from the Wii.
Installing Nintendo Wii Motherboard

Step 41
Carefully grab the motherboard by its edges and lift it
off the bottom panel.
To reassemble your device, follow these instructions in reverse order.
Installing Nintendo Wii Motherboard

Nintendo Wii open maken, 3.0 out of 5 based on 2 ratings